Arduino 0018用のMakefile

MacOSX用のMakefileを作った.といっても既存のものを環境に合わせただけですが.

project1というプロジェクトの場合,
mkdir project1
として,このファイルをその中に入れる.
project1.pde
というファイルに普通にArduinoのコードを書く.
make
make upload
とする.linuxでもlNSTALL_DIRなどを自分の環境に合わせると同様にできるはず.
avrdudeの所を変えれば,ブレッドボード上の素のatmega168とかにポケットプログラマーで焼けそうな感じ.これでIDEとハードウェアの制約から自由に\(^O^)/

この手でsanguinoも行けそうと思ったが,

$ make
/Applications/Arduino.app/Contents/Resources/Java/hardware/tools/avr/bin/avr-gcc -Os -lm -Wl,--gc-sections -mmcu=atmega644p -o applet/sanguino_test.elf applet/sanguino_test.o applet/core.a
/Applications/Arduino.app/Contents/Resources/Java/hardware/tools/avr/bin/../lib/gcc/avr/4.3.2/../../../../avr/lib/avr5/crtm644p.o:(.init9+0x0): undefined reference to `main'
make: *** [applet/sanguino_test.elf] Error 1

原因はよくわからない.

#-----
# Arduino 0018 Makefile
# modified to use on MacOSX by stastaka (2010/02/08)
# Arduino adaptation by mellis, eighthave, oli.keller
#
# This makefile allows you to build sketches from the command line
# without the Arduino environment (or Java).
#
# Detailed instructions for using the makefile:
#
#  1. Copy this file into the folder with your sketch. There should be a
#     file with the same name as the folder and with the extension .pde
#     (e.g. foo.pde in the foo/ folder).
#
#  2. Modify the line containg "INSTALL_DIR" to point to the directory that
#     contains the Arduino installation (for example, under Mac OS X, this
#     might be /Applications/arduino-0012).
#
#  3. Modify the line containing "PORT" to refer to the filename
#     representing the USB or serial connection to your Arduino board
#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*).
#
#  4. Set the line containing "MCU" to match your board's processor.
#     Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
#     or Diecimila have the atmega168.  If you're using a LilyPad Arduino,
#     change F_CPU to 8000000.
#
#  5. At the command line, change to the directory containing your
#     program's file and the makefile.
#
#  6. Type "make" and press enter to compile/verify your program.
#
#  7. Type "make upload", reset your Arduino board, and press enter to
#     upload your program to the Arduino board.
#
# $Id$

TARGET = $(notdir $(CURDIR))
#INSTALL_DIR = $(HOME)/arduino-0018
INSTALL_DIR = /Applications/Arduino.app/Contents/Resources/Java
#PORT = /dev/ttyUSB*
PORT = /dev/cu.usbserial*
UPLOAD_RATE = 57600
AVRDUDE_PROGRAMMER = stk500v1
#MCU = atmega168
MCU = atmega328p
F_CPU = 16000000

############################################################################
# Below here nothing should be changed...

VERSION=18
ARDUINO = $(INSTALL_DIR)/hardware/arduino/cores/arduino
AVR_TOOLS_PATH = $(INSTALL_DIR)/hardware/tools/avr/bin
#AVR_TOOLS_PATH = /usr/bin
#AVR_TOOLS_PATH = /usr/local/CrossPack-AVR/bin
AVRDUDE_PATH = $(INSTALL_DIR)/hardware/tools/avr/bin
C_MODULES =  ¥
$(ARDUINO)/wiring_pulse.c ¥
$(ARDUINO)/wiring_analog.c ¥
$(ARDUINO)/pins_arduino.c ¥
$(ARDUINO)/wiring.c ¥
$(ARDUINO)/wiring_digital.c ¥
$(ARDUINO)/WInterrupts.c ¥
$(ARDUINO)/wiring_shift.c ¥
# end of C_MODULES

CXX_MODULES = ¥
$(ARDUINO)/Tone.cpp ¥
$(ARDUINO)/main.cpp ¥
$(ARDUINO)/WMath.cpp ¥
$(ARDUINO)/Print.cpp ¥
$(ARDUINO)/HardwareSerial.cpp ¥
# end of CXX_MODULES

CXX_APP = applet/$(TARGET).cpp
MODULES = $(C_MODULES) $(CXX_MODULES)
SRC = $(C_MODULES)
CXXSRC = $(CXX_MODULES) $(CXX_APP)
FORMAT = ihex


# Name of this Makefile (used for "make depend").
MAKEFILE = Makefile

# Debugging format.
# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
#DEBUG = stabs
DEBUG =

OPT = s

# Place -D or -U options here
CDEFS = -DF_CPU=$(F_CPU)L -DARDUINO=$(VERSION)
CXXDEFS = -DF_CPU=$(F_CPU)L -DARDUINO=$(VERSION)

# Place -I options here
CINCS = -I$(ARDUINO)
CXXINCS = -I$(ARDUINO)

# Compiler flag to set the C Standard level.
# c89   - "ANSI" C
# gnu89 - c89 plus GCC extensions
# c99   - ISO C99 standard (not yet fully implemented)
# gnu99 - c99 plus GCC extensions
#CSTANDARD = -std=gnu99
CDEBUG = -g$(DEBUG)
#CWARN = -Wall -Wstrict-prototypes
#CWARN = -Wall   # show all warnings
CWARN = -w      # suppress all warnings
####CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
CTUNING = -ffunction-sections -fdata-sections
CXXTUNING = -fno-exceptions -ffunction-sections -fdata-sections
#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)

CFLAGS = $(CDEBUG) -O$(OPT) $(CWARN) $(CTUNING) $(CDEFS) $(CINCS) $(CSTANDARD) $(CEXTRA)
CXXFLAGS = $(CDEBUG) -O$(OPT) $(CWARN) $(CXXTUNING) $(CDEFS) $(CINCS)
#ASFLAGS = -Wa,-adhlns=$( applet/$(TARGET).cpp
	echo 'void setup();' >> applet/$(TARGET).cpp
	echo 'void loop();' >> applet/$(TARGET).cpp
	cat $(TARGET).pde >> applet/$(TARGET).cpp

elf: applet/$(TARGET).elf
hex: applet/$(TARGET).hex
eep: applet/$(TARGET).eep
lss: applet/$(TARGET).lss
sym: applet/$(TARGET).sym

# Program the device.  
upload: applet/$(TARGET).hex
	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)


	# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) applet/$(TARGET).hex
ELFSIZE = $(SIZE)  applet/$(TARGET).elf
sizebefore:
	@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi

sizeafter:
	@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(HEXSIZE); echo; fi


# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT=$(OBJCOPY) --debugging ¥
--change-section-address .data-0x800000 ¥
--change-section-address .bss-0x800000 ¥
--change-section-address .noinit-0x800000 ¥
--change-section-address .eeprom-0x810000


coff: applet/$(TARGET).elf
	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf $(TARGET).cof


extcoff: $(TARGET).elf
	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf $(TARGET).cof


.SUFFIXES: .elf .hex .eep .lss .sym

.elf.hex:
	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@

.elf.eep:
	$(OBJCOPY) -O $(FORMAT) -j .eeprom --set-section-flags=.eeprom="alloc,load" ¥
	--no-change-warnings ¥
	--change-section-lma .eeprom=0 $< $@

# Create extended listing file from ELF output file.
.elf.lss:
	$(OBJDUMP) -h -S $ $@

# Create a symbol table from ELF output file.
.elf.sym:
	$(NM) -n $ $@

	# Link: create ELF output file from library.
#applet/$(TARGET).elf: $(TARGET).pde applet/core.a
applet/$(TARGET).elf: applet/$(TARGET).o applet/core.a
	$(LD) $(ALL_LDFLAGS) -o $@ applet/$(TARGET).o applet/core.a

applet/core.a: $(OBJ_MODULES)
	@for i in $(OBJ_MODULES); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done



# Compile: create object files from C++ source files.
.cpp.o:
	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@

# Compile: create object files from C source files.
.c.o:
	$(CC) -c $(ALL_CFLAGS) $< -o $@


# Compile: create assembler files from C source files.
.c.s:
	$(CC) -S $(ALL_CFLAGS) $< -o $@


# Assemble: create object files from assembler source files.
.S.o:
	$(CC) -c $(ALL_ASFLAGS) $< -o $@


# Automatic dependencies
%.d: %.c
	$(CC) -M $(ALL_CFLAGS) $ $@

%.d: %.cpp
	$(CXX) -M $(ALL_CXXFLAGS) $ $@


# Target: clean project.
clean:
	$(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf ¥
	applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a ¥
	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)

.PHONY:	all build elf hex eep lss sym program coff extcoff clean applet_files sizebefore sizeafter

#include $(SRC:.c=.d)
#include $(CXXSRC:.cpp=.d) 
#-----
広告
カテゴリー: Arduino

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト / 変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト / 変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト / 変更 )

Google+ フォト

Google+ アカウントを使ってコメントしています。 ログアウト / 変更 )

%s と連携中

カテゴリー
2010年2月
« 1月   3月 »
1234567
891011121314
15161718192021
22232425262728
%d人のブロガーが「いいね」をつけました。